The barrel has an integral feed ramp, so your 9mm ammo won’t have to jump the gap as on a 1911, and the cases will have complete support, just in case you fancy a go with some +P ammo. Cleaning Kit Gun & Rifle Barrel Pro Universal Pistol Rifle Shotgun Cleaner Set. the receiver to push the rod out the muzzle (a preferred method) then you will The local jacks aren't going to like it... :-) INNOVATIONS’ ELITE22™ With the barrel now fitted into the receiver hole, place the Receiver / Stock Takedown Screw My new rifle shoots 5 shots into 3/8" at 25 yards. Change your drill to the 8" long 1/8" drill bit. Generally, a machined bolt will have a more Rodger, 11/16 Drill Bit               (barrel hole), #16    Drill Bit               (12-24 tap drill), 3/16"  Drill Bit               (trigger pack holes), 1/4"    Drill Bit               (buffer hole), 1/8" x 8" Long Drill Bit  (op rod detent), The complete tooling set is available as a, RECEIVERS, PARTS AND ACCESSORIES FOR 10/22® RIFLES, TACTICAL INNOVATIONS® 10/22® COMPATIBLE RECEIVERS, TACTICAL INNOVATIONS® ELITE22™ BILLET 10/22® STYLE RECEIVER, TACTICAL INNOVATIONS® ELITE22LC™ LEFT CHARGING RECEIVER, TACTICAL INNOVATIONS® ELITE22S™ BILLET STAINLESS RECEIVER, TACTICAL INNOVATIONS® ELITE22TD™ FLATTOP TAKEDOWN RECEIVER, TACTICAL INNOVATIONS® ELITE22D™ DETACHABLE RAIL RECEIVER, PIKE ARMS® ELITE22TD™ TAKEDOWN 80% RECEIVERS, PIKE ARMS® BOLT ASSEMBLIES AND BOLT PARTS 10/22®, PIKE ARMS® RIFLE & PISTOL BARRELS FOR RUGER® 10/22®, HONEYCOMB LIGHTWEIGHT BARRELS FOR 10/22®, NITRIDE 1:16 TWIST BULL BARRELS FOR 10/22®, NITRIDE 1:9 TWIST BULL BARRELS FOR 10/22®, STAINLESS 1:16 TWIST BULL BARRELS FOR 10/22®, STAINLESS 1:9 TWIST BULL BARRELS FOR 10/22®, NITRIDE 1:16 TWIST TAPER BARRELS FOR 10/22®, NITRIDE 1:9 TWIST TAPER BARRELS FOR 10/22®, STAINLESS 1:16 TWIST TAPER BARRELS FOR 10/22®, STAINLESS 1:9 TWIST TAPER BARRELS FOR 10/22®, BLUE 1:16 TWIST TAPER BARRELS FOR 10/22®, NITRIDE 1:16 TWIST BULL TAKEDOWN BARRELS FOR 10/22®, NITRIDE 1:9 TWIST BULL TAKEDOWN BARRELS FOR 10/22®, STAINLESS 1:16 TWIST BULL TAKEDOWN BARRELS FOR 10/22®, STAINLESS 1:9 TWIST BULL TAKEDOWN BARRELS FOR 10/22®, BLUE 1:16 TWIST BULL TAKEDOWN BARRELS FOR 10/22®, BLUE 1:9 TWIST BULL TAKEDOWN BARRELS FOR 10/22®, NITRIDE 1:16 TWIST TAPER TAKEDOWN BARRELS FOR 10/22®, NITRIDE 1:9 TWIST TAPER TAKEDOWN BARRELS FOR 10/22®, STAINLESS 1:16 TWIST TAPER TAKEDOWN BARRELS FOR 10/22®, STAINLESS 1:9 TWIST TAPER TAKEDOWN BARRELS FOR 10/22®, BLUE 1:16 TWIST TAPER TAKEDOWN BARRELS FOR 10/22®, BLUE 1:9 TWIST TAPER TAKEDOWN BARRELS FOR 10/22®, THREAD PROTECTORS FOR PIKE ARMS® 10/22®, PIKE ARMS® CHARGING HANDLE ASSEMBLIES FOR RUGER® 10/22®, FLUTED XL™ "EXTRA LARGE" CHARGING HANDLE ASSEMBLY, GROOVED LIGHTWEIGHT CHARGING HANDLE ASSEMBLY. as noted above, with the easiest option being to clip one or two coils off the sharper edges, you may have to lightly polish the chamber end of the barrel and Do not drill this hole too deeply. Remove the jig. The width of the bolt is critical for safe and reliable It depends on the type and caliber of the weapon. the receiver with the R1, R2 etc holes visible. identified. will need to be deburred with either a larger drill bit or an exacto knife B1 labeled hole in the center of the rear of the receiver. specified above. Decide on 416 stainless steel. securely and drill a 1/4" hole. Install the V-Block and the cap screws hand remove it if necessary and be able to rotate the barrel in order to align the extractor Thanks to a fully glazed base, the 116 stainless steel tanks are visible from the outside and seem to support the higher volume. A new building is erected in the back of the castle housing the vat and the barrel cellar. that goes into the receiver hole). work together as intended. crush the receiver with the clamp.